Do and don't guide for your agent: instrument makers
This guide gives an instrument or controls maker ten plain do and don't rules for an AI agent, covering specifications, readings, calibration promises and safety. Use it as the base of your agent's instructions.
Runs in your browser. Nothing you enter is sent anywhere or saved.
Before you start
Technicians and lab staff are sharp readers. They notice a wrong unit, a vague range or an over-friendly tone about a serious topic. An agent that talks to them needs clear boundaries so it is helpful on the routine and quiet on the things that need judgement.
Use this list as a starting point for your agent's written instructions. Cut what does not apply to your range, add rules for your own products, and read it aloud to your service team. If they disagree with a line, that is useful to know before a customer finds out.
Tick each one as you go. 0 of 10 done.
[ ] Do ask for the model and serial number before answering a technical question. [ ] Do repeat published specifications exactly as your data sheet states them. [ ] Do give the manual or data sheet link for the exact model. [ ] Do say plainly when a person will take over and who it is. [ ] Do collect the symptom, reading and last calibration date for service. [ ] Don't interpret a measurement or say a reading is right or wrong. [ ] Don't advise on using an instrument outside its stated range. [ ] Don't promise a calibration date unless it is open in the calendar. [ ] Don't answer any question about patients, treatment or safety yourself. [ ] Don't guess when the answer is not in your notes.
Why the line matters in this trade
A restaurant that gives a wrong opening time loses a table. A maker that gives a wrong calibration interval may cost a customer an audit, or leave a faulty meter in use. The same agent that is cheerful about a spare probe must be careful about anything that touches a decision.
The simplest test is this: is the agent repeating something you wrote down, or forming a view? Repeating is fine. Forming a view goes to a person.
Adding your own rules
Every range has quirks, so add lines that match yours.
- Name the products that must only be serviced by your own technicians.
- List the accessories that look alike but do not fit.
- State which firmware versions still receive support.
- Say how you want serial numbers written back to the customer.
FAQ
Can the agent quote a specification at all?
Yes, when it is a published figure in your own data sheet and the agent knows the exact model. It should quote it as written and give the link, and not stretch it to cover unusual conditions.
Why not let the agent explain readings?
A reading depends on setup, environment, calibration and use. Explaining it is a professional judgement, and a wrong explanation could lead a customer to trust a faulty instrument or reject a good one.
How do we keep these rules up to date?
Review them each time a product launches or a field issue appears. A short monthly check with your service lead is enough to keep the agent's rules in line with what your team really says.
More free tools for instrument and controls makers
- First-reply checklist for instrument and controls makers
- Hand-over rules checklist for instrument and controls makers
- First-week checklist for instrument and controls makers
- Weekly chat review checklist for instrument and controls makers
- Busy-season checklist for instrument and controls makers
- Customer privacy checklist for instrument and controls makers
- Greeting messages for instrument and controls makers
- After-hours replies for instrument and controls makers
- Booking and order confirmations for instrument and controls makers
- Reminder messages for instrument and controls makers
- Apology and complaint replies for instrument and controls makers
- "Let me check" replies for instrument and controls makers
- Follow-up messages for instrument and controls makers
- Review request messages for instrument and controls makers
- Price and quote replies for instrument and controls makers
- Delay and stock notices for instrument and controls makers
- Thank-you messages for instrument and controls makers
- Hand-over notes for instrument and controls makers
- Ready answers for instrument and controls makers
- Holiday and closure notices for instrument and controls makers
- Missed enquiries calculator for instrument and controls makers
- AI agent instructions builder for instrument and controls makers
- Auto-reply message writer for instrument and controls makers
- FAQ answer sheet for instrument and controls makers
- Reply speed scorecard for instrument and controls makers
- Is your business ready for an AI agent? Quiz for instrument and controls makers
- Message workload planner for instrument and controls makers
- Hours saved calculator for instrument and controls makers
- Enquiry-to-customer value estimator for instrument and controls makers
Read the guide: Answer technician and lab messages for instrument and controls makers.