Weekly chat review checklist for instrument makers
This checklist helps an instrument or controls maker review a week of AI agent conversations. It shows what to look for in answers about ranges, calibration, service and safety handovers.
Runs in your browser. Nothing you enter is sent anywhere or saved.
Before you start
An agent that answers customers needs the same attention as a new member of staff. In your trade the cost of a wrong figure is higher than in most, because a technician may act on a stated range or a calibration interval. A short weekly review catches errors while they are small.
Set aside thirty minutes on the same day each week. Open a sample of conversations, including a few that went well and every one that was handed over. Go through the list and note what to fix in the agent's notes before next week.
Tick each one as you go. 0 of 10 done.
[ ] Check every range, limit and interval quoted against your data sheets. [ ] Read every chat that touched a medical or safety topic. [ ] Look at chats where the customer repeated a question. [ ] Check each calibration booking against the service calendar. [ ] Review handover notes for missing model or serial numbers. [ ] Note any model or part the agent did not recognise. [ ] Count chats that ended with no clear next step. [ ] Check the tone on any complaint or delay message. [ ] List any question that came up three or more times. [ ] Write down three changes to make before next week.
Reading the week as a whole
Look beyond single chats. If many customers ask about the same accessory, perhaps the data sheet hides it. If many ask how to reset a display, perhaps the manual buries the step. The chats are a free window into what your documents fail to say.
Share the three changes with your service team and your product team. Instrument makers who feed customer questions back into their manuals often find fewer messages arrive at all.
What to do with a wrong answer
When you find a mistake, move quickly and in order.
- Fix the note so the agent stops repeating it.
- Contact the customer with the correct figure.
- Search other chats for the same wrong answer.
- Record what happened so the team learns from it.
FAQ
How many conversations should I read each week?
Read every handed-over chat and every safety-related one, plus a random sample of around ten others. That gives a fair picture without taking more than half an hour once you are in the habit.
Who in our company should do the review?
Ideally someone who knows the products well, such as a service lead or application engineer. They can spot a wrong range or a mixed-up model at a glance, which a general office reader might miss.
What if a review finds the agent said something unsafe?
Treat it as an incident. Correct the notes immediately, contact the customer, tell your safety lead, and tighten the handover rules so that topic goes to a person in future.
More free tools for instrument and controls makers
- First-reply checklist for instrument and controls makers
- Hand-over rules checklist for instrument and controls makers
- First-week checklist for instrument and controls makers
- Busy-season checklist for instrument and controls makers
- Customer privacy checklist for instrument and controls makers
- Do and don't guide for your agent: instrument and controls makers
- Greeting messages for instrument and controls makers
- After-hours replies for instrument and controls makers
- Booking and order confirmations for instrument and controls makers
- Reminder messages for instrument and controls makers
- Apology and complaint replies for instrument and controls makers
- "Let me check" replies for instrument and controls makers
- Follow-up messages for instrument and controls makers
- Review request messages for instrument and controls makers
- Price and quote replies for instrument and controls makers
- Delay and stock notices for instrument and controls makers
- Thank-you messages for instrument and controls makers
- Hand-over notes for instrument and controls makers
- Ready answers for instrument and controls makers
- Holiday and closure notices for instrument and controls makers
- Missed enquiries calculator for instrument and controls makers
- AI agent instructions builder for instrument and controls makers
- Auto-reply message writer for instrument and controls makers
- FAQ answer sheet for instrument and controls makers
- Reply speed scorecard for instrument and controls makers
- Is your business ready for an AI agent? Quiz for instrument and controls makers
- Message workload planner for instrument and controls makers
- Hours saved calculator for instrument and controls makers
- Enquiry-to-customer value estimator for instrument and controls makers
Read the guide: Answer technician and lab messages for instrument and controls makers.