Do and don't guide for your agent: spring and wire makers
This guide gives plain do and don't rules for an AI agent answering customers of a spring or wire product maker. It helps you set clear limits on measurements, loads, prices and hand-overs.
Runs in your browser. Nothing you enter is sent anywhere or saved.
Before you start
An agent follows the rules you give it. In a spring and wire shop the stakes are small on some questions, like how to measure a coil, and large on others, like whether a spring will hold a person's weight. Clear do and don't rules mark that line so nobody has to guess.
Read each rule and keep the ones that suit you. Add your own at the bottom for the quirks of your shop. Then hand the finished list to whoever sets up the agent, and read it again after the first month of real chats.
Tick each one as you go. 0 of 10 done.
[ ] Do ask for wire diameter, outside diameter, free length and quantity before passing on a request. [ ] Do explain how to measure a spring using simple words and a picture. [ ] Do use your own wire sizes, finishes and minimums when you answer. [ ] Do hand over every question about load, fatigue or safety use. [ ] Do say clearly when a person will reply and by roughly when. [ ] Don't state a load rating, cycle life or fit to a machine. [ ] Don't quote a price for a custom spring or wire form. [ ] Don't promise a delivery date that a person has not confirmed. [ ] Don't suggest a different material or finish without a person agreeing. [ ] Don't message anyone who has not written to you first.
Why the don't rules matter most
Most mistakes in this trade come from a confident answer to a question that needed an engineer. A friendly agent that says that is one for our engineer is far safer than one that guesses. Customers accept a short wait for a straight answer.
Write your don't rules in the same plain words you would use with a new starter. If a rule needs a reason, include it, such as because a failed spring in a gate can injure someone. Reasons help the agent apply the rule in cases you did not list.
Add rules of your own
Think about these shop-specific points.
- Do keep replies short enough to read on a phone at the machine.
- Don't discuss another customer's parts or prices.
- Do point repeat buyers to the part number on their last order.
- Don't argue with an upset customer; hand the chat over.
FAQ
How many rules should I give my agent?
Ten to twenty clear ones is plenty to start. Cover measurements, ranges, price, load and delivery dates, then add a rule whenever a real chat shows a gap in what the agent does.
Will the agent follow every rule?
It follows them well, but no tool is perfect. Read a sample of chats each week to check, and tighten any rule where you see a slip, especially around load and safety.
Can I change the rules later?
Yes, and you should. Your products, stock and lead times change, so update the list whenever they do, and after any chat that surprised you.
More free tools for spring and wire product makers
- First-reply checklist for spring and wire product makers
- Hand-over rules checklist for spring and wire product makers
- First-week checklist for spring and wire product makers
- Weekly chat review checklist for spring and wire product makers
- Busy-season checklist for spring and wire product makers
- Customer privacy checklist for spring and wire product makers
- Greeting messages for spring and wire product makers
- After-hours replies for spring and wire product makers
- Booking and order confirmations for spring and wire product makers
- Reminder messages for spring and wire product makers
- Apology and complaint replies for spring and wire product makers
- "Let me check" replies for spring and wire product makers
- Follow-up messages for spring and wire product makers
- Review request messages for spring and wire product makers
- Price and quote replies for spring and wire product makers
- Delay and stock notices for spring and wire product makers
- Thank-you messages for spring and wire product makers
- Hand-over notes for spring and wire product makers
- Ready answers for spring and wire product makers
- Holiday and closure notices for spring and wire product makers
- Missed enquiries calculator for spring and wire product makers
- AI agent instructions builder for spring and wire product makers
- Auto-reply message writer for spring and wire product makers
- FAQ answer sheet for spring and wire product makers
- Reply speed scorecard for spring and wire product makers
- Is your business ready for an AI agent? Quiz for spring and wire product makers
- Message workload planner for spring and wire product makers
- Hours saved calculator for spring and wire product makers
- Enquiry-to-customer value estimator for spring and wire product makers
Read the guide: Answer spring and wire product messages without losing the drawing.